Externes SCSI-RAID an Adaptec-HBA

19/03/2015 - 14:10 von Christian Schmidt | Report spam
Liebe Gemeinde,

an einem Server mit via PCI-Express dazugestecktem
Adaptec ASC-29320ALP ist ein easyRAID-Speichersystem angeschlossen. Auf
diesem habe ich ein etwas voluminöseres RAID6 eingerichtet, das in zwei
Slices unterteilt ist, die via SCSI an den Server "herausgereicht"
werden sollen. Was allerdings nicht klappt, ist der Zugriff darauf:

# gdisk /dev/sdb
GPT fdisk (gdisk) version 0.8.5

Problem opening /dev/sdb for reading! Error is 6.

# ls -l /dev/sdb
brw-rwT 1 root disk 8, 16 Mar 19 10:36 /dev/sdb

Dasselbe Problem besteht mit /dev/sdc.

Auf dem Server werkelt ein aktuelles Wheezy:
# uname -a
Linux HOSTNAME 3.2.0-4-amd64 #1 SMP Debian 3.2.65-1+deb7u2 x86_64 GNU/Linux

Nachfolgend findet Ihr den Output von "dmesg | grep -i scsi". Zu
beachten ist, dass neben dem SCSI-Controller noch ein
3ware-SATA-RAID-Controller in der Maschine steckt, der aber tadellos
funktioniert.

- schnipp -
[ 1.044596] scsi1 : ahci
[ 1.044709] scsi2 : ahci
[ 1.044777] scsi3 : ahci
[ 1.044844] scsi4 : ahci
[ 1.044911] scsi5 : ahci
[ 1.044977] scsi6 : ahci
[ 1.204030] scsi0 : 3ware 9000 Storage Controller
[ 1.204125] 3w-9xxx: scsi0: Found a 3ware 9000 Storage Controller at
0xdfb00000, IRQ: 16.
[ 1.380538] scsi 5:0:0:0: CD-ROM HL-DT-ST DVDRAM GT20N
CW03 PQ: 0 ANSI: 5
[ 1.389962] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw
xa/form2 cdda tray
[ 1.390148] sr 5:0:0:0: Attached scsi CD-ROM sr0
[ 1.391757] sr 5:0:0:0: Attached scsi generic sg0 type 5
[ 1.540088] 3w-9xxx: scsi0: Firmware FE9X 4.08.00.006, BIOS BE9X
4.08.00.001, Ports: 2.
[ 1.540513] scsi 0:0:0:0: Direct-Access AMCC 9650SE-2LP DISK
4.08 PQ: 0 ANSI: 5
[ 1.550038] scsi 0:0:0:0: Attached scsi generic sg1 type 0
[ 16.100045] scsi7 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
[ 16.153432] scsi: waiting for bus probes to complete ...
[ 16.357654] scsi 7:0:1:0: Direct-Access easyRAID Q16+
R0.0 PQ: 0 ANSI: 5
[ 16.357663] scsi target7:0:1: asynchronous
[ 16.357666] scsi7:A:1:0: Tagged Queuing enabled. Depth 32
[ 16.357677] scsi target7:0:1: Beginning Domain Validation
[ 16.359235] scsi target7:0:1: wide asynchronous
[ 16.360437] scsi target7:0:1: FAST-160 WIDE SCSI 320.0 MB/s DT IU RTI
WRFLOW PCOMP (6.25 ns, offset 127)
[ 16.390568] scsi target7:0:1: Ending Domain Validation
[ 16.391085] scsi 7:0:1:1: Direct-Access easyRAID Q16+
R0.0 PQ: 0 ANSI: 5
[ 16.391091] scsi7:A:1:1: Tagged Queuing enabled. Depth 32
[ 19.730394] sd 7:0:1:0: Attached scsi generic sg2 type 0
[ 19.730928] sd 7:0:1:1: Attached scsi generic sg3 type 0
[ 49.888591] scsi7: At time of recovery, card was not paused
[ 49.888599] scsi7: Dumping Card State at program address 0x9 Mode 0x33
[ 49.888801] scsi7: FIFO0 Free, LONGJMP == 0x826c, SCB 0x3
[ 49.888879] scsi7: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
[ 49.888993] scsi7: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE = 0x52
[ 49.888998] scsi7: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x1
[ 49.889002] scsi7: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
[ 49.889023] scsi7: REG0 == 0xffff, SINDEX = 0x104, DINDEX = 0x104
[ 49.889033] scsi7: SCBPTR == 0x3, SCB_NEXT == 0xff80, SCB_NEXT2 == 0xff02
[ 49.889119] (scsi7:A:1:1): Device is disconnected, re-queuing SCB
[ 49.889149] scsi7: Recovery code sleeping
[ 50.659580] scsi7: Device reset code sleeping
[ 50.916410] scsi7: Device reset returning 0x2002
[ 51.173180] scsi7: Device reset code sleeping
[ 51.430033] scsi7: Device reset returning 0x2002
[ 95.841119] scsi7: At time of recovery, card was not paused
[ 95.841128] scsi7: Dumping Card State at program address 0x20 Mode 0x22
[ 95.841360] scsi7: FIFO0 Free, LONGJMP == 0x826c, SCB 0x3
[ 95.841446] scsi7: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
[ 95.841570] scsi7: LQISTATE = 0x1, LQOSTATE = 0x1a, OPTIONMODE = 0x52
[ 95.841575] scsi7: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
[ 95.841580] scsi7: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
[ 95.841602] scsi7: REG0 == 0x3, SINDEX = 0x104, DINDEX = 0x104
[ 95.841614] scsi7: SCBPTR == 0xff03, SCB_NEXT == 0xff00, SCB_NEXT2 == 0x0
[ 95.841691] scsi7:0:1:1: Cmd aborted from QINFIFO
[ 105.841603] scsi7: At time of recovery, card was not paused
[ 105.841612] scsi7: Dumping Card State at program address 0x0 Mode 0x22
[ 105.841833] scsi7: FIFO0 Free, LONGJMP == 0x826c, SCB 0x3
[ 105.841920] scsi7: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
[ 105.842043] scsi7: LQISTATE = 0x1, LQOSTATE = 0x1a, OPTIONMODE = 0x52
[ 105.842048] scsi7: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
[ 105.842053] scsi7: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
[ 105.842076] scsi7: REG0 == 0x3, SINDEX = 0x104, DINDEX = 0x104
[ 105.842087] scsi7: SCBPTR == 0xff03, SCB_NEXT == 0xff00, SCB_NEXT2 == 0x0
[ 105.842148] scsi7:0:1:1: Cmd aborted from QINFIFO
[ 105.842190] scsi7: Device reset code sleeping
[ 110.840016] scsi7: Device reset timer expired (active 1)
[ 110.840020] scsi7: Device reset returning 0x2003
- schnapp -

Seltsam erscheint mir die Meldung "At time of recovery, card was not
paused", aber mir sind mittlerweile die sinnvoll erscheinenden
Kombinationen von Suchbegriffen ausgegangen.

Wenn ich im dmesg-Output nach "sd*" greppe, gibt es folgende Treffer
(/dev/sda ist das 3ware-RAID):

- schnipp -
[ 1.551995] sd 0:0:0:0: [sda] 488259584 512-byte logical blocks: (249
GB/232 GiB)
[ 1.552511] sd 0:0:0:0: [sda] Write Protect is off
[ 1.552516] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
[ 1.552868] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.584402] sda: sda1 sda2 sda3
[ 1.585661] sd 0:0:0:0: [sda] Attached SCSI disk
[ 19.730394] sd 7:0:1:0: Attached scsi generic sg2 type 0
[ 19.730599] sd 7:0:1:0: [sdb] 1218850816 2048-byte logical blocks:
(2.49 TB/2.26 TiB)
[ 19.730928] sd 7:0:1:1: Attached scsi generic sg3 type 0
[ 19.731075] sd 7:0:1:0: [sdb] Write Protect is off
[ 19.731079] sd 7:0:1:0: [sdb] Mode Sense: bf 00 00 08
[ 49.888046] sd 7:0:1:1: Attempting to queue an ABORT message:CDB: 0x0
0x0 0x0 0x0 0x0 0x0
[ 50.145959] sd 7:0:1:0: Attempting to queue an ABORT message:CDB:
0x1a 0x0 0x8 0x0 0x20 0x0
[ 50.145964] sd 7:0:1:0: Command not found
[ 50.659573] sd 7:0:1:0: Attempting to queue a TARGET RESET
message:CDB: 0x1a 0x0 0x8 0x0 0x20 0x0
[ 51.173174] sd 7:0:1:1: Attempting to queue a TARGET RESET
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
[ 61.718129] sd 7:0:1:0: Device offlined - not ready after error recovery
[ 61.718153] sd 7:0:1:0: [sdb] No Caching mode page found
[ 61.718247] sd 7:0:1:0: [sdb] Assuming drive cache: write through
[ 61.718532] sd 7:0:1:0: [sdb] Attached SCSI disk
[ 61.720316] sd 7:0:1:1: [sdc] 1218850816 2048-byte logical blocks:
(2.49 TB/2.26 TiB)
[ 61.720789] sd 7:0:1:1: [sdc] Write Protect is off
[ 61.720792] sd 7:0:1:1: [sdc] Mode Sense: bf 00 00 08
[ 61.721129] sd 7:0:1:1: [sdc] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 61.721477] sd 7:0:1:1: [sdc] 1218850816 2048-byte logical blocks:
(2.49 TB/2.26 TiB)
[ 61.737198] sdc: unknown partition table
[ 61.737537] sd 7:0:1:1: [sdc] 1218850816 2048-byte logical blocks:
(2.49 TB/2.26 TiB)
[ 61.738321] sd 7:0:1:1: [sdc] Attached SCSI disk
[ 62.354994] EXT4-fs (sda3): mounted filesystem with ordered data
mode. Opts: (null)
[ 95.840062] sd 7:0:1:1: [sdc] Attempting to queue an ABORT
message:CDB: 0x28 0x0 0x0 0x0 0x0 0x44 0x0 0x0 0x2 0x0
[ 105.840017] sd 7:0:1:1: [sdc] Attempting to queue an ABORT
message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
[ 105.842181] sd 7:0:1:1: [sdc] Attempting to queue a TARGET RESET
message:CDB: 0x28 0x0 0x0 0x0 0x0 0x44 0x0 0x0 0x2 0x0
[ 120.848843] sd 7:0:1:1: Device offlined - not ready after error recovery
[ 120.848854] sd 7:0:1:1: [sdc] Unhandled error code
[ 120.848857] sd 7:0:1:1: [sdc] Result: hostbyte=DID_BUS_BUSY
driverbyte=DRIVER_OK
[ 120.848862] sd 7:0:1:1: [sdc] CDB: Read(10): 28 00 00 00 00 44 00 00
02 00
[ 120.848877] end_request: I/O error, dev sdc, sector 272
[ 120.848958] Buffer I/O error on device sdc, logical block 34
[ 120.849063] sd 7:0:1:1: rejecting I/O to offline device
[ 120.849183] sd 7:0:1:1: rejecting I/O to offline device
[ 120.849267] sd 7:0:1:1: rejecting I/O to offline device
[ 120.849358] sd 7:0:1:1: rejecting I/O to offline device
[ 120.849441] sd 7:0:1:1: rejecting I/O to offline device
[ 120.849533] sd 7:0:1:1: rejecting I/O to offline device
[ 122.115533] Adding 3905532k swap on /dev/sda1. Priority:-1 extents:1
across:3905532k
[ 122.143470] EXT4-fs (sda3): re-mounted. Opts: (null)
[ 122.639417] EXT4-fs (sda3): re-mounted. Opts: errors=remount-ro
[ 123.478451] EXT4-fs (sda2): mounted filesystem with ordered data
mode. Opts: (null)
[ 124.592190] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).


Hat jemand einen Hinweis, in welche Richtung ich bohren sollte? Gerne
liefere ich noch weitere Informationen nach, wenn nötig.

Gruß & Dank,
Christian

No signature available.


Zum AUSTRAGEN schicken Sie eine Mail an debian-user-german-REQUEST@lists.debian.org
mit dem Subject "unsubscribe". Probleme? Mail an listmaster@lists.debian.org (engl)
Archive: https://lists.debian.org/550AC8F9.2040406@chemie.uni-hamburg.de
 

Lesen sie die antworten

#1 Christian Schmidt
23/03/2015 - 21:30 | Warnen spam
On 19.03.2015 14:02, Christian Schmidt wrote:
an einem Server mit via PCI-Express dazugestecktem
Adaptec ASC-29320ALP ist ein easyRAID-Speichersystem angeschlossen. Auf
diesem habe ich ein etwas voluminöseres RAID6 eingerichtet, das in zwei
Slices unterteilt ist, die via SCSI an den Server "herausgereicht"
werden sollen. Was allerdings nicht klappt, ist der Zugriff darauf:



Liest hier kein SCSI-Kenner mehr mit? ;-)

Gruß,
Christian


Zum AUSTRAGEN schicken Sie eine Mail an
mit dem Subject "unsubscribe". Probleme? Mail an (engl)
Archive: https://lists.debian.org/

Ähnliche fragen