FC8: shutdown hängt

19/01/2008 - 12:07 von Ralph Stahl | Report spam
Moin,

gelegentlich hàngt shutdown -h now oder auch reboot ohne erkennbaren
Grund. /var/log/messages zeigt nichts dazu. Das System arbeitet weiter,
als wàre nichts gewesen. "Hàngen" heißt, daß der in der Shell
eingegebene Befehl einfach nicht "wiederkommt" und auch nicht abbrechbar
ist. Mit top sehe ich auch keinen Prozeß, der gerade heftig am Laufen
ist; ps zeigt keinen "toten" Prozeß. Mir bleibt dann nur, die
Plattenaktivitàt zu beàugen (gkrellm) und bei scheinbarer Ruhe mutig ein
Reset mit dem Knöpfchen zu machen.

Wie kann ich dem auf die Spur kommen? Provozieren kann ich das nicht.
Gibt es sowas wie ein "Gegenstück" zu dmesg, das das shutdown protokolliert?

Ralph

PS:

KDE/Gnome zwar installiert, nutze aber IceWM.
Immer laufende Anwendungen:
gkrellm 2.3 mit xmbmon 2.0.5,
Thunderbird 2.0 und Pidgin 2.3.1-1.fc8 (hàngt uach ohne beides)

dmesg:

Linux version 2.6.23.9-85.fc8
(kojibuilder@xenbuilder4.fedora.phx.redhat.com) (gcc version 4.1.2
20070925 (Red Hat 4.1.2-33)) #1 SMP Fri Dec 7 15:49:59 EST 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ffec000 (usable)
BIOS-e820: 000000003ffec000 - 000000003ffef000 (ACPI data)
BIOS-e820: 000000003ffef000 - 000000003ffff000 (reserved)
BIOS-e820: 000000003ffff000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
Using x86 segment limits to approximate NX protection
Entering add_active_range(0, 0, 262124) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 262124
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 262124
On node 0 totalpages: 262124
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 255 pages used for memmap
HighMem zone: 32493 pages, LIFO batch:7
Movable zone: 0 pages used for memmap
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP 000F67C0, 0014 (r0 ASUS )
ACPI: RSDT 3FFEC000, 002C (r1 ASUS A7V-133 30303031 MSFT 31313031)
ACPI: FACP 3FFEC080, 0074 (r1 ASUS A7V-133 30303031 MSFT 31313031)
ACPI: DSDT 3FFEC100, 2C2B (r1 ASUS A7V-133 1000 MSFT 100000B)
ACPI: FACS 3FFFF000, 0040
ACPI: BOOT 3FFEC040, 0028 (r1 ASUS A7V-133 30303031 MSFT 31313031)
ACPI: PM-Timer IO Port: 0xe408
Allocating PCI resources starting at 50000000 (gap: 40000000:bfff0000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
Built 1 zonelists in Zone order. Total pages: 260077
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffb000 (0180f000)
Enabling fast FPU save and restore... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c07a8000 soft=c0788000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1009.016 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1030668k/1048496k available (2184k kernel code, 17072k reserved,
1116k data, 280k init, 130992k highmem)
virtual kernel memory layout:
fixmap : 0xffc53000 - 0xfffff000 (3760 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc073f000 - 0xc0785000 ( 280 kB)
.data : 0xc06222f5 - 0xc0739544 (1116 kB)
.text : 0xc0400000 - 0xc06222f5 (2184 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs", HWalign2, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 2019.53 BogoMIPS
(lpj09766)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0183f9ff c1c7f9ff 00000000 00000000
00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0183f1ff c1c7f9ff 00000000 00000420 00000000
00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 14k freed
ACPI: Core revision 20070126
ACPI: setting ELCR to 0200 (from 0c80)
CPU0: AMD Athlon(tm) Processor stepping 02
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
sizeof(vma)„ bytes
sizeof(page)2 bytes
sizeof(inode)36 bytes
sizeof(dentry)2 bytes
sizeof(ext3inode)H8 bytes
sizeof(buffer_head)V bytes
sizeof(skbuff)0 bytes
sizeof(task_struct)52 bytes
Booting paravirtualized kernel on bare hardware
Time: 10:21:41 Date: 01/19/08
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf1150, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
Disabling VIA memory write queue (PCI ID 0305, rev 03): [55] 28 & 1f -> 08
PCI quirk: region e200-e27f claimed by vt82c686 HW-mon
PCI quirk: region e800-e80f claimed by vt82c686 SMB
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *7 9 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
PCI: BIOS reporting unknown device 00:58
PCI: Device 0000:00:0b.1 not found by BIOS
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
Time: tsc clocksource has been installed.
pnp: 00:00: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:00: iomem range 0xf0000-0xfffff could not be reserved
pnp: 00:00: iomem range 0x100000-0x3fffffff could not be reserved
pnp: 00:00: iomem range 0xfffe0000-0xffffffff could not be reserved
pnp: 00:03: ioport range 0xe400-0xe47f has been reserved
pnp: 00:03: ioport range 0xe800-0xe80f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: d000-dfff
MEM window: d7000000-d7dfffff
PREFETCH window: d7f00000-e3ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Switched to high resolution mode on CPU 0
Freeing initrd memory: 3592k freed
Simple Boot Flag at 0x3a set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1200738101.831:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
ksign: Installing public key data
Loading keyring
- Added public key 4BB254D1F8000763
- User ID: Red Hat, Inc. (Kernel Module GPG key)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Applying VIA southbridge workaround.
PCI: VIA PCI bridge detected. Disabling DAC.
PCI: Disabling Via external APIC routing
Boot video device is 0000:01:00.0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 16 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102
agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
agpgart: AGP aperture is 64M @ 0xe4000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
input: Macintosh mouse button emulation as /class/input/input0
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please
boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Processor cpuid 642 not supported
Using IPI No-Shortcut mode
Magic number: 8:278:376
Freeing unused kernel memory: 280k freed
Write protecting the kernel read-only data: 844k
Marking TSC unstable due to: TSC halts in idle.
Time: acpi_pm clocksource has been installed.
PCI: Enabling device 0000:00:0b.2 (0014 -> 0016)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.2[C] -> Link [LNKD] -> GSI 7 (level, low)
-> IRQ 7
ehci_hcd 0000:00:0b.2: EHCI Host Controller
ehci_hcd 0000:00:0b.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0b.2: irq 7, io mem 0xd5000000
ehci_hcd 0000:00:0b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:0b.0 (0014 -> 0016)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKB] -> GSI 10 (level,
low) -> IRQ 10
ohci_hcd 0000:00:0b.0: OHCI Host Controller
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0b.0: irq 10, io mem 0xd6000000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
PCI: Enabling device 0000:00:0b.1 (0014 -> 0016)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LNKC] -> GSI 11 (level,
low) -> IRQ 11
ohci_hcd 0000:00:0b.1: OHCI Host Controller
ohci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:0b.1: irq 11, io mem 0xd5800000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-5: new high speed USB device using ehci_hcd and address 3
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:04.2[D] -> Link [LNKD] -> GSI 7 (level, low)
-> IRQ 7
uhci_hcd 0000:00:04.2: UHCI Host Controller
uhci_hcd 0000:00:04.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:04.2: irq 7, io base 0x0000b400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-5: configuration #1 chosen from 1 choice
hub 1-5:1.0: USB hub found
hub 1-5:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:04.3[D] -> Link [LNKD] -> GSI 7 (level, low)
-> IRQ 7
uhci_hcd 0000:00:04.3: UHCI Host Controller
uhci_hcd 0000:00:04.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:04.3: irq 7, io base 0x0000b000
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
SCSI subsystem initialized
libata version 2.21 loaded.
pata_via 0000:00:04.1: version 0.3.2
scsi0 : pata_via
scsi1 : pata_via
ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001b800
irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001b808
irq 15
usb 2-1: new low speed USB device using ohci_hcd and address 2
ata1.00: ATA-6: WDC WD800BB-00JHC0, 05.01C05, max UDMA/100
ata1.00: 156301488 sectors, multi 16: LBA
ata1.00: limited to UDMA/33 due to 40-wire cable
ata1.00: configured for UDMA/33
usb 2-1: configuration #1 chosen from 1 choice
input: HID 1241:1177 as /class/input/input2
input: USB HID v1.00 Mouse [HID 1241:1177] on usb-0000:00:0b.0-1
ata2.00: ATAPI: HL-DT-STDVD-RAM GSA-H55N, 1.02, max UDMA/66
ata2.00: limited to UDMA/33 due to 40-wire cable
ata2.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA WDC WD800BB-00JH 05.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 1:0:0:0: CD-ROM HL-DT-ST DVD-RAM GSA-H55N 1.02 PQ: 0 ANSI: 5
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised:
dm-devel@redhat.com
ACPI: PCI Interrupt 0000:00:11.0[A] -> Link [LNKB] -> GSI 10 (level,
low) -> IRQ 10
scsi2 : pata_pdc202xx_old
scsi3 : pata_pdc202xx_old
ata3: PATA max UDMA/100 cmd 0x00018800 ctl 0x00018402 bmdma 0x00017400
irq 10
ata4: PATA max UDMA/100 cmd 0x00018000 ctl 0x00017802 bmdma 0x00017408
irq 10
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1200738110.628:2): selinux=0 auidB94967295
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x0
parport_pc: VIA parallel port disabled in BIOS
input: PC Speaker as /class/input/input3
via686a 0000:00:04.4: Sensors disabled, enable with force_addr=0xe200
8139too Fast Ethernet driver 0.9.28
PCI: Enabling device 0000:00:0a.0 (0004 -> 0007)
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 11 (level,
low) -> IRQ 11
eth0: RealTek RTL8139 at 0xf88fa000, 00:50:bf:2d:77:8c, IRQ 11
eth0: Identified 8139 chip type 'RTL-8139C'
input: Power Button (FF) as /class/input/input4
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input5
ACPI: Power Button (CM) [PWRB]
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
PCI: Enabling device 0000:00:0d.0 (0004 -> 0005)
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKD] -> GSI 7 (level, low)
-> IRQ 7
floppy0: no floppy controllers found
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level,
low) -> IRQ 11
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized radeon 1.28.0 20060524 on minor 0
device-mapper: multipath: version 1.0.5 loaded
loop: module loaded
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2031608k swap on /dev/mapper/VolGroup00-LogVol01. Priority:-1
extents:1 across:2031608k
ip6_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
audit(1200734539.295:3): audit_pid10 old=0 by auidB94967295
eth0: no IPv6 routers present
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[drm] Setting GART location based on new memory map
[drm] writeback test succeeded in 1 usecs
 

Lesen sie die antworten

#1 zsekeres
20/01/2008 - 14:22 | Warnen spam
Moin,

On Jan 19, 12:07 pm, Ralph Stahl wrote:
gelegentlich hàngt shutdown -h now oder auch reboot ohne erkennbaren
Grund. /var/log/messages zeigt nichts dazu. Das System arbeitet weiter,
als wàre nichts gewesen. "Hàngen" heißt, daß der in der Shell
eingegebene Befehl einfach nicht "wiederkommt" und auch nicht abbrechbar
ist. Mit top sehe ich auch keinen Prozeß, der gerade heftig am Laufen
ist; ps zeigt keinen "toten" Prozeß. Mir bleibt dann nur, die
Plattenaktivitàt zu beàugen (gkrellm) und bei scheinbarer Ruhe mutig ein
Reset mit dem Knöpfchen zu machen.

Wie kann ich dem auf die Spur kommen? Provozieren kann ich das nicht.
Gibt es sowas wie ein "Gegenstück" zu dmesg, das das shutdown protokolliert?



Schau doch mal, ob in /var/log/messages (wenn sich das seit FC5 nicht
geàndert hat ;-) noch etwas steht. Am besten in einem Terminal ein
"tail -f /var/log/messages" absetzen, im anderen Terminal dann das
System herunterfahren.

Oder evtl. mit "strace poweroff" nachsehen, wo das Herunterfahren
hàngen
bleibt.

Viel Glück,
Zoltan

Ähnliche fragen