SATA-Fehler

17/10/2007 - 12:01 von Jan Schmidt | Report spam
Hallo NG,

was will mir der Rechner damit sagen?

Die ata-Fehler scheinen nur beim Booten zu erscheinen - Zugriff auf
die Platte funktioniert - bis jetzt - fehlerfrei.

NB: - ist ein openSuSE 10.2 drauf
- lspci meldet

00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA


Gruß,
Jan.

ata1: SATA max UDMA/133 cmd 0xDC81C100 ctl 0x0 bmdma 0x0 irq 11
ata2: SATA max UDMA/133 cmd 0xDC81C180 ctl 0x0 bmdma 0x0 irq 11
ata3: SATA max UDMA/133 cmd 0xDC81C200 ctl 0x0 bmdma 0x0 irq 11
ata4: SATA max UDMA/133 cmd 0xDC81C280 ctl 0x0 bmdma 0x0 irq 11
scsi0 : ahci
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7, max UDMA/133, 156301488 sectors: LBA48 NCQ (depth 31/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi1 : ahci
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATAPI, max UDMA/100
ata2.00: configured for UDMA/100
scsi2 : ahci
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATA-7, max UDMA7, 586072368 sectors: LBA48 NCQ (depth 31/32)
ata3.00: ata3: dev 0 multi count 16
ata3.00: configured for UDMA/133
scsi3 : ahci
ata4: SATA link down (SStatus 0 SControl 300)
Vendor: ATA Model: WDC WD800JD-55MU Rev: 10.0
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
Vendor: HL-DT-ST Model: DVD-ROM GDRH10N Rev: 0F04
Type: CD-ROM ANSI SCSI revision: 05
Vendor: ATA Model: SAMSUNG HD300LJ Rev: ZT10
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 586072368 512-byte hdwr sectors (300069 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 586072368 512-byte hdwr sectors (300069 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
sdb: sdb1
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Attached scsi generic sg1 type 5
sd 2:0:0:0: Attached scsi disk sdb
sd 2:0:0:0: Attached scsi generic sg2 type 0
ATIIXP: IDE controller at PCI slot 0000:00:14.1
ATIIXP: chipset revision 0
ATIIXP: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x8420-0x8427, BIOS settings: hda:pio, hdb:pio
ATIIXP: simplex device: DMA disabled
ide1: ATIIXP Bus-Master DMA disabled (BIOS)
Probing IDE interface ide0...
ata2.00: exception Emask 0x40 SAct 0x0 SErr 0x800 action 0x2
ata2.00: (irq_stat 0x40000001)
ata2.00: cmd a0/00:00:00:00:20/00:00:00:00:00/a0 tag 0 cdb 0x0 data 0 in
res 51/64:03:00:00:20/00:00:00:00:00/a0 Emask 0x40 (internal error)
ata2: soft resetting port
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Probing IDE interface ide1...
ata2.00: configured for UDMA/100
ata2: EH complete
ata2.00: exception Emask 0x40 SAct 0x0 SErr 0x800 action 0x2
ata2.00: (irq_stat 0x40000001)
ata2.00: cmd a0/00:00:00:00:20/00:00:00:00:00/a0 tag 0 cdb 0x0 data 0 in
res 51/24:03:00:00:20/00:00:00:00:00/a0 Emask 0x40 (internal error)
ata2: soft resetting port
BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
EDD information not available.
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: configured for UDMA/100
ata2: EH complete
ata2.00: exception Emask 0x40 SAct 0x0 SErr 0x800 action 0x2
ata2.00: (irq_stat 0x40000001)
ata2.00: cmd a0/00:00:00:00:20/00:00:00:00:00/a0 tag 0 cdb 0x0 data 0 in
res 51/24:03:00:00:20/00:00:00:00:00/a0 Emask 0x40 (internal error)
ata2: soft resetting port
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)

usw. usf.
 

Lesen sie die antworten

#1 Sven Hartge
17/10/2007 - 22:47 | Warnen spam
Jan Schmidt wrote:

was will mir der Rechner damit sagen?



Vermutlich gar nichts.

Die ata-Fehler scheinen nur beim Booten zu erscheinen - Zugriff auf
die Platte funktioniert - bis jetzt - fehlerfrei.



Tauchen diese Meldungen beim Starten von smartd o.à. auf? Wenn ja:
bekanntes (kosmetisches) Problem.



Sven Hartge -- professioneller Unix-Geek
Meine Gedanken im Netz: http://www.svenhartge.de/

Ähnliche fragen